industrial temperature range idt74alvch162269a 3.3v cmos 12-bit to 24-bit registered bus exchanger 1 january 2004 industrial temperature range the idt logo is a registered trademark of integrated device technology, inc. ? 2004 integrated device technology, inc. dsc-4239/2 features: ? 0.5 micron cmos technology ? typical t sk(o) (output skew) < 250ps ? esd > 2000v per mil-std-883, method 3015; > 200v using machine model (c = 200pf, r = 0) ?v cc = 3.3v 0.3v, normal range ?v cc = 2.7v to 3.6v, extended range ?v cc = 2.5v 0.2v ? cmos power levels (0.4 w typ. static) ? rail-to-rail output swing for increased noise margin ? available in ssop and tssop packages functional block diagram applications: ? 3.3v high speed systems ? 3.3v and lower voltage computing systems drive features: ? balanced output drivers: 12ma ? low switching noise idt74alvchr162269a 3.3v cmos 12-bit to 24-bit registered bus exchanger with 3-state outputs and bus-hold description: this 12-bit to 24-bit registered bus exchanger is used in applications in which two separate ports must be multiplexed onto, or demultiplexed from, a single port. it is particularly suitable as an interface between synchronous drams and high-speed microprocessors. data is stored in the internal b-port registers on the low-to-high transition of the clock (clk) input when the appropriate clock-enable ( clkena ) inputs are low. proper control of these inputs allows two sequential 12-bit words to be presented as a 24-bit word on the b-port. for data transfer in the b-to-a direction, a single storage register is provided. the select sel line selects 1b or 2b data for the a outputs. the register on the a output permits the fastest possible data transfer, thus extending the period during which the data is valid on the bus. the control terminals are registered so that all transactions are synchronous with clk. data flow is controlled by the active-low output enables ( oea , oeb1 and oeb2 ). the alvchr162269a has series resistors in the device output struc- ture which will significantly reduce line noise when used with light loads. this driver has been designed to drive 12ma at the designated threshold levels. the alvchr162269a has ?bus-hold? which retains the inputs? last state whenever the input goes to a high impedance. this prevents floating inputs and eliminates the need for pull-up/down resistors. oeb 2 oeb 1 clk clkena 1 oea 1 b 1 sel 0 1 clkena 2 c1 1d c1 1d c1 1d c1 1d c1 1d ce 1d c1 ce 1d c1 a 1 2 b 1 1 of 12 channels 29 2 56 30 55 28 1 23 6 8
industrial temperature range 2 idt74alvch162269a 3.3v cmos 12-bit to 24-bit registered bus exchanger ssop/ tssop top view pin configuration symbol description max unit v term (2) terminal voltage with respect to gnd ?0.5 to +4.6 v v term (3) terminal voltage with respect to gnd ?0.5 to v cc +0.5 v t stg storage temperature ?65 to +150 c i out dc output current ?50 to +50 ma i ik continuous clamp current, 50 ma v i < 0 or v i > v cc i ok continuous clamp current, v o < 0 ?50 ma i cc continuous current through each 100 ma i ss v cc or gnd absolute maximum ratings (1) notes: 1. stresses greater than those listed under absolute maximum ratings may cause permanent damage to the device. this is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. exposure to absolute maximum rating conditions for extended periods may affect reliability. 2. v cc terminals. 3. all terminals except v cc . notes: 1. h = high voltage level l = low voltage level x = don?t care z = high impedance = low-to-high transition 2. output level before the indicated steady-state input conditions were established. note: 1. as applicable to the device type. symbol parameter (1) conditions typ. max. unit c in input capacitance v in = 0v 5 7 pf c out output capacitance v out = 0v 7 9 pf c i/o i/o port capacitance v in = 0v 7 9 pf capacitance (t a = +25c, f = 1.0mhz) function tables (1) inputs outputs clkena1 clkena2 clk ax 1 bx 2 bx hhxx 1 b (2) 2 b (2) lx ll x lx hh x xl lx l xl hx h a-to-b storage ( oeb = l) inputs outputs clk oea oebx ax 1 bx, 2 bx hh z z h l z active l h active z l l active active output enable inputs outputs clk sel 1 bx 2 bx ax xh xx a (2) xl xx a (2) hlx l hhx h lxl l lxh h b-to-a storage ( oea = l) oea 2 b 3 gnd 2 b 2 2 b 1 v cc a 1 a 2 gnd a 3 a 4 a 5 a 6 a 8 a 9 gnd a 10 a 11 a 12 v cc 1 b 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 48 49 50 51 52 53 54 55 56 1 oeb 2 2 b 4 gnd 2 b 5 2 b 6 v cc 2 b 7 2 b 8 2 b 9 2 b 10 2 b 11 2 b 12 gnd 1 b 11 1 b 10 1 b 9 1 b 8 gnd 1 b 7 1 b 6 1 b 5 gnd 1 b 3 nc sel 25 26 27 28 32 31 30 29 gnd 1 b 4 clkena 1 clk a 7 1 b 2 v cc 1 b 12 oeb 1 clkena 2
industrial temperature range idt74alvch162269a 3.3v cmos 12-bit to 24-bit registered bus exchanger 3 note: 1. these pins have "bus-hold". all other pins are standard inputs, outputs, or i/os. symbol parameter test conditions min. typ. (1) max. unit v ih input high voltage level v cc = 2.3v to 2.7v 1.7 ? ? v v cc = 2.7v to 3.6v 2 ? ? v il input low voltage level v cc = 2.3v to 2.7v ? ? 0.7 v v cc = 2.7v to 3.6v ? ? 0.8 i ih input high current v cc = 3.6v v i = v cc ?? 5a i il input low current v cc = 3.6v v i = gnd ? ? 5a i ozh high impedance output current v cc = 3.6v v o = v cc ?? 10 a i ozl (3-state output pins) v o = gnd ? ? 10 v ik clamp diode voltage v cc = 2.3v, i in = ?18ma ? ?0.7 ?1.2 v v h input hysteresis v cc = 3.3v ? 100 ? mv i ccl quiescent power supply current v cc = 3.6v ? 0.1 40 a i cch v in = gnd or v cc i ccz ? i cc quiescent power supply current one input at v cc - 0.6v, other inputs at v cc or gnd ? ? 750 a variation dc electrical characteristics over operating range following conditions apply unless otherwise specified: operating condition: t a = ?40c to +85c note: 1. typical values are at v cc = 3.3v, +25c ambient. pin description pin names i/o description ax (1:12) i/o bidirectional data port a. usually connected to the cpu?s address/data bus. (1) 1bx (1:12) i/o bidirectional data port 1b. usually connected to the even path or even bank of memory. (1) 2bx (1:12) i/o bidirectional data port 2b. usually connected to the odd path or odd bank of memory. (1) clk i clock input clkena1 i clock enable input for the a-1b register. if clkena1 is low during the rising edge of clk, data will be clocked into register a-1b (active low). clkena2 i clock enable input for the a-2b register. if clkena2 is low during the rising edge of clk, data will be clocked into register a-2b (active low). sel i 1b or 2b port selection. when high during the rising edge of clk, sel enables data transfer from 1b port to a port. when low during the rising edge of clk, sel enables data transfer from 2b port to a port. oea i synchronous output enable for a port (active low) oeb1 i synchronous output enable for 1b port (active low) oeb2 i synchronous output enable for 2b port (active low)
industrial temperature range 4 idt74alvch162269a 3.3v cmos 12-bit to 24-bit registered bus exchanger operating characteristics, t a = 25c v cc = 2.5v 0.2v v cc = 3.3v 0.3v symbol parameter test conditions typical typical unit c pd power dissipation capacitance outputs enabled c l = 0pf, f = 10mhz 142 172 pf c pd power dissipation capacitance outputs disabled 115 129 bus-hold characteristics symbol parameter (1) test conditions min. typ. (2) max. unit i bhh bus-hold input sustain current v cc = 3v v i = 2v ? 75 ? ? a i bhl v i = 0.8v 75 ? ? i bhh bus-hold input sustain current v cc = 2.3v v i = 1.7v ? 45 ? ? a i bhl v i = 0.7v 45 ? ? i bhho bus-hold input overdrive current v cc = 3.6v v i = 0 to 3.6v ? ? 500 a i bhlo notes: 1. pins with bus-hold are identified in the pin description. 2. typical values are at v cc = 3.3v, +25c ambient. note: 1. v ih and v il must be within the min. or max. range shown in the dc electrical characteristics over operating range table for the appropriat e v cc range. t a = ? 40c to + 85c. output drive characteristics symbol parameter test conditions (1) min. max. unit v oh output high voltage v cc = 2.3v to 3.6v i oh = ? 0.1ma v cc ? 0.2 ? v v cc = 2.3v i oh = ? 4ma 1.9 ? i oh = ? 6ma 1.7 ? v cc = 2.7v i oh = ? 4ma 2.2 ? i oh = ? 8ma 2 ? v cc = 3v i oh = ? 6ma 2.4 ? i oh = ? 12ma 2 ? v ol output low voltage v cc = 2.3v to 3.6v i ol = 0.1ma ? 0.2 v v cc = 2.3v i ol = 4ma ? 0.4 i ol = 6ma ? 0.55 v cc = 2.7v i ol = 4ma ? 0.4 i ol = 8ma ? 0.6 v cc = 3v i ol = 6ma ? 0.55 i ol = 12ma ? 0.8
industrial temperature range idt74alvch162269a 3.3v cmos 12-bit to 24-bit registered bus exchanger 5 notes: 1. see test circuits and waveforms. t a = ? 40c to + 85c. 2. skew between any two outputs of the same package and switching in the same direction. switching characteristics (1) v cc = 2.5v 0.2v v cc = 2.7v v cc = 3.3v 0.15v v cc = 3.3v 0.3v symbol parameter min. max. min. max. min. max. min. max. unit f clock clock frequency ? 95 ? 115 ? 135 ? 135 mhz t plh propagation delay 2.3 7.7 ? 6.9 2.3 5 2.2 5.8 ns t phl clk to xbx t plh propagation delay 1.9 6.4 ? 5.8 2 4 2 5.2 ns t phl clk to ax t pzh output enable time 2.5 7.7 ? 6.9 2.3 5 2.3 5.8 ns t pzl clk to xbx t pzh output enable time 2.2 6.7 ? 6 2.1 4.3 2.1 5.3 ns t pzl clk to ax t phz output disable time 3.3 8.1 ? 6.7 2.3 5.3 2.4 6 ns t plz clk to xbx t phz output disable time 2.7 8 ? 6.2 2.2 5.4 2.1 6 ns t plz clk to ax t su set-up time, ax data before clk 1.4 ? 1.4 ? 0.9 ? 1 ? ns t su set-up time, bx data before clk 1.6 ? 1.5 ? 1 ? 1.1 ? ns t su set-up time, sel before clk 0.8 ? 1.1 ? 1.3 ? 1.3 ? ns t su set-up time, clkena1 or clkena2 before clk 0.8 ? 1 ? 0.7 ? 0.8 ? ns t su set-up time, oebx or oea before clk 1.7 ? 1.6 ? 1.1 ? 1.2 ? ns t h hold time, ax data after clk 0.9 ? 0.9 ? 1.1 ? 1.2 ? ns t h hold time, bx data after clk 0.8 ? 0.6 ? 0.8 ? 1 ? ns t h hold time, sel after clk 1.1 ? 0.8 ? 1.6 ? 1.7 ? ns t h hold time, clkena1 or clkena2 after clk 1.4 ? 1 ? 1.4 ? 1.6 ? ns t h hold time, oebx or oea after clk 0.9 ? 0.8 ? 1 ? 1.2 ? ns t w pulse width, clk high or low 5.2 ? 4.3 ? 3.3 ? 3.3 ? ns t sk (o) output skew (2) ?????500?500ps
industrial temperature range 6 idt74alvch162269a 3.3v cmos 12-bit to 24-bit registered bus exchanger open v load gnd v cc pulse generator d.u.t. 500 ? 500 ? c l r t v in v out (1, 2) alvc link input v ih 0v v oh v ol t plh1 t sk (x) output 1 output 2 t phl1 t sk (x) t plh2 t phl2 v t v t v oh v t v ol t sk (x) = t plh2 - t plh1 or t phl2 - t phl1 alvc link same phase input transition opposite phase input transition 0v 0v v oh v ol t plh t phl t phl t plh output v ih v t v t v ih v t alvc link data input 0v 0v 0v 0v t rem timing input synchronous control t su t h t su t h v ih v t v ih v t v ih v t v ih v t alvc link asynchronous control low-high-low pulse high-low-high pulse v t t w v t alvc link control input t plz 0v output normally low t pzh 0v switch closed output normally high enable disable switch open t phz 0v v lz v oh v t v t t pzl v load/2 v load/2 v ih v t v ol v hz alvc link test circuits and waveforms propagation delay test circuit for all outputs enable and disable times set-up, hold, and release times notes: 1. for t sk (o) output1 and output2 are any two outputs. 2. for t sk (b) output1 and output2 are in the same bank. definitions: c l = load capacitance: includes jig and probe capacitance. r t = termination resistance: should be equal to z out of the pulse generator. notes: 1. pulse generator for all pulses: rate 1.0mhz; t f 2.5ns; t r 2.5ns. 2. pulse generator for all pulses: rate 1.0mhz; t f 2ns; t r 2ns. output skew - t sk ( x ) pulse width note: 1. diagram shown for input control enable-low and input control disable-high. symbol v cc (1) = 3.3v0.3v v cc (1) = 2.7v v cc (2) = 2.5v0.2v unit v load 6 6 2 x vcc v v ih 2.7 2.7 vcc v v t 1.5 1.5 vcc / 2 v v lz 300 300 150 mv v hz 300 300 150 mv c l 50 50 30 pf test conditions switch position test switch open drain disable low v load enable low disable high gnd enable high all other tests open
industrial temperature range idt74alvch162269a 3.3v cmos 12-bit to 24-bit registered bus exchanger 7 ordering information corporate headquarters for sales: for tech support: 2975 stender way 800-345-7015 or 408-727-6116 logichelp@idt.com santa clara, ca 95054 fax: 408-492-8674 (408) 654-6459 www.idt.com idt xx alvc xxx xx package device type temp. range pv pa r162 74 shrink small outline package thin shrink small outline package 12-bit to 24-bit registered bus exchanger with 3-state outputs ? 40c to +85c xxx family bus-hold 269a bus-hold double-density with resistors, 12ma h
|
